Welcome to the Rx7 Forum and Owners Club.
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

<<<<<< Register to remove these ads >>>>>>


Go Back   Rx7 Forum and Owners Club > General RX-7 Area > TECH Support

TECH Support Technical Support for your RX7, Open 24/7/365. Post your problems and see if someone can help!


Reply
 
Thread Tools Display Modes
Old 05-06-2004, 04:58 AM   #11
 
black rocket's Avatar
black rocket
Full Access Member
 
Join Date: May 2004
Location: NV
Posts: 1,059
Default
You can't even get wiring harness from the dealer, so best bet is to go to junk yard and get one. You can't swap s4 and s5 (you can't use s5 wire for s4, visaversa)

And if and when you get the harness be careful removing them connectors as they are just as brittle as wires.

My suggestion is to replace that particular wire/wires completely and wrap it with thermal tape unless you want to cook that one, too .

I know a guy who redone his harness completely with new wires. (told me took him 2 weeks)


__________________
Drive safe and Sane
black rocket is offline   Reply With Quote
Old 05-06-2004, 05:01 AM   #12
AusTexRex
Full Access Member
 
Join Date: Apr 2004
Location: Austin & Waco Texas
Posts: 553
Send a message via AIM to AusTexRex
Default
Originally Posted by black rocket
You can't even get wiring harness from the dealer, so best bet is to go to junk yard and get one. You can't swap s4 and s5 (you can't use s5 wire for s4, visaversa)
The ones I was referring to are salvaged ones that Mazda South here in Austin has in their parts warehouse.
AusTexRex is offline   Reply With Quote
Old 05-06-2004, 05:03 AM   #13
 
black rocket's Avatar
black rocket
Full Access Member
 
Join Date: May 2004
Location: NV
Posts: 1,059
Default
Originally Posted by fc velocity
ill put up a pic as soon as i can get a camra. every thing happened about six months ago i blow my clutch at 145 mph on the highway racing friends. i brought it to a shop to put in the cluch in, when they were done the trany was f*@ked. i had my landlord in the car to take him home did a smoke show and all of a souden my tack stopped working the light on the tack even stopped working but the car was still running i shut off the car at his house and it would not turn over sence that day.
Hope you didn't short out anything. Ck your fuses.


__________________
Drive safe and Sane
black rocket is offline   Reply With Quote
Old 05-06-2004, 05:04 AM   #14
 
black rocket's Avatar
black rocket
Full Access Member
 
Join Date: May 2004
Location: NV
Posts: 1,059
Default
Originally Posted by AusTexRex
Originally Posted by black rocket
You can't even get wiring harness from the dealer, so best bet is to go to junk yard and get one. You can't swap s4 and s5 (you can't use s5 wire for s4, visaversa)
The ones I was referring to are salvaged ones that Mazda South here in Austin has in their parts warehouse.
How much are they asking for one?


__________________
Drive safe and Sane
black rocket is offline   Reply With Quote
Old 05-06-2004, 05:20 AM   #15
AusTexRex
Full Access Member
 
Join Date: Apr 2004
Location: Austin & Waco Texas
Posts: 553
Send a message via AIM to AusTexRex
Default
I'll call and find out
AusTexRex is offline   Reply With Quote
Old 05-08-2004, 02:01 AM   #16
Hollywood
Full Access Member
 
Join Date: May 2004
Posts: 170
Send a message via AIM to Hollywood
Default
sounds like a good excuse to get a stand alone ECU
Hollywood is offline   Reply With Quote
Old 05-08-2004, 02:13 AM   #17
2ROTORMOTOR
Full Access Member
 
Join Date: Mar 2004
Location: Miami
Posts: 319
Send a message via AIM to 2ROTORMOTOR Send a message via MSN to 2ROTORMOTOR
Default
Originally Posted by Hollywood
sounds like a good excuse to get a stand alone ECU
yup Haltech all the way...


__________________
2ROTORMOTOR is offline   Reply With Quote
Old 05-09-2004, 04:06 PM   #18
Hollywood
Full Access Member
 
Join Date: May 2004
Posts: 170
Send a message via AIM to Hollywood
Default
haltechs the shit!!! i am running an E6X
Hollywood is offline   Reply With Quote
Old 05-12-2004, 01:22 AM   #19
fc velocity
Junior Member
 
Join Date: Apr 2004
Posts: 10
Default
sorry guys coputer has been down people are asking between $100 and $500 do u guys think a 90 wireing harness ill go on a 88 engine if i change the intank over
fc velocity is offline   Reply With Quote
Old 05-12-2004, 01:24 AM   #20
fc velocity
Junior Member
 
Join Date: Apr 2004
Posts: 10
Default
how much do an ecu go for
fc velocity is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump