3rd gen rx7 engine and Mictotech EMS

[ka9568]

I was looking for some help with a 3rd gen engine (1994 twin turbo) and a microtech LT10. I built a hovercraft and going to use this engine. The engine is connected to 2 fans. I am having trouble getting the engine started. I have to put oil in the spark holes to get it started and then it will run for a while and then quit. This engine has not been modified. I am new to this microtech EMS. I really want this to be simple and tried using TPS mode but, have messed up the default maps and the original map was not saved from the factory. I do not want to send back to Australia. I have also tried some of the base maps I found on line but, they are modified and my engine keeps flooding. Any help would be greatly appreciated.

Idle Map
Screen 1

30" ~ 1.38
25" ~ 1.48
20" ~ 1.33
15" ~ 1.71
10" ~ 1.71
05" ~ 1.62
00" ~ 2.00
2-20psi ~ 4.95

Load Map
Screen 3

30" ~ 0.95
25" ~ 1.19
20" ~ 1.33
15" ~ 1.71
10" ~ 2.14
05" ~ 2.57
00" ~ 2.86
2psi ~ 2.2
4psi ~ 3.05
6psi ~ 3.7
8psi ~ 4.1
10psi ~ 4.7
14psi ~ 5.2
16psi ~ 5.6
18psi ~ 5.8
20psi ~ 6.2

RPMwot Map Screen 17

5000 ~ 05
5500 ~ 08
6000 ~ 08
6500 ~ 10
7000 ~ 11
7500 ~ 11
8000 ~ 11
9000 ~ 12

The rest are zero

RPMcrs Screen 18

1000 ~ -12
1500 ~ -11
2000 ~ -12

THe rest are zero



Pump Map
Screen 19

Pump2Start ~ 2000
Pump1Amt ~ 00
Pump1Pulse ~ 04
Pump1Trig ~ 18
Pump1Stop ~ 00
Pump1Adv ~ 05

Pump2Time ~ 10
Pump2Amt ~ 30
Pump2Trig ~ 16
Pump2Stop ~ 00
Pump2Adv ~ 05

PumpDwell ~ 3.00
PumpTimers ~ No
Pump1Sync ~ No
PumpSpare ~ 00
PumpCold ~ 00

Water Map
Screen 20

-25 ~ 0
-17 ~ 70
-9 ~ 60
-01 ~ 50
05 ~ 45
11 ~ 45
18 ~ 42
24 ~ 34
31 ~ 26
38 ~ 24
46 ~ 19
60 ~ 12
68 ~ 06
82 ~ 0
99 ~ 0
124 ~ 0

Air_t Map
Screen 21

-25 ~ 0
-17 ~ 8
-9 ~ 6
-1 ~ 5
5 ~ 4
11 ~ 3
18 ~ 3
24 ~ 0
31 ~ 0
38 ~ 0
46 ~ 0
60 ~ 0
68 ~ 0
82 ~ 0
99 ~ 0
124 ~ 0

Crank Map
Screen 22

-25 ~ 72
-17 ~ 72
-9 ~ 72
-1 ~ 67
5 ~ 62
11 ~ 57
18 ~ 50
24 ~ 41
31 ~ 31
38 ~ 26
46 ~ 20
60 ~ 15
68 ~ 5
82 ~ 0
99 ~ 0
124 ~ 0

t*rpm
Screen 23

Idle ~ 20
1000 ~ 20
1500 ~ 20
2000 ~ 20
2500 ~ 25
3000 ~ 25
3500 ~ 25
4000 ~ 25
4500 ~ 25
5000 ~ 25
5500 ~ 25
6000 ~ 25
6500 ~ 25
7000 ~ 25
7500 ~ ??
8000 ~ 25
9000 ~ 25

t*map Map
Screen 24

Idle ~ 00
25 ~ 05
20 ~ 04
15 ~ 03
10 ~ 02
05 ~ 00
00 ~ 00
2psi ~ 00
4psi ~ 00
6psi ~ 02
8psi ~ -04
10psi ~ -06
14psi ~ -10
16psi ~ -12
18 psi ~ -16
20 psi ~ -20

t*air Screen 25
Correction value Is expressed as number of degrees you wish to advance or Retard to the Ignition curve and values Is set at zero.

t*gap
Screen 26

0500 ~ 15
1000 ~ 15
1500 ~ 15
2000 ~ 14
2500 ~ 12
3000 ~ 10
3500 ~ 10
4000 ~ 10
4500 ~ 10
5000 ~ 10
5500 ~ 10
6000 ~ 10
6500 ~ 10
7000 ~ 10
8000 ~ 10

t*Inj Map
Screen 27

0500 ~ 120
1000 ~ 150
1500 ~ 150
2000 ~ 150
2500 ~ 150
3000 ~ 150
3500 ~ 150
4000 ~ 150
4500 ~ 180
5000 ~ 210
5500 ~ 210
6000 ~ 240
6500 ~ 240
7000 ~ 270
8000 ~ 270
9000 ~ 270

t*wat Map Screen 28


ANd the rest are zero

Option Map
Screen 30

Af_StE ~ 10
Dwell ~ 3.25 *set at Time Base - not at Duty Cycle*
REVstg ~ 1320
MAPstg ~ 02"
%stg ~ 50

[BoostedFC]

Tuning & wiring is not my thing, maybe some here can help. Where are you located at? Maybe I can refer you to someone near you.

[ka9568]

I live in Kosciusko, Mississippi. 60 miles north of Jackson.



Thanks

[BoostedFC]

Contact the guys at Speed1
http://www.speed1allentown.com/